oe7drt-website

dominic

oe7drt-website

14 KiB

Raw Blame History

title

summary

date

lastmod

coverCaption

Digirig

The Digirig gets controlled with rigctld -- I use different models for the HF and the FM rig -- but the rig configuration is the same for both:

  "hamlib_rigs": {
    "my_rig": {
      "address": "127.0.0.1:4532",
      "network": "tcp"
    }
  },

That part of the pat configuration makes sure that pat can transmit with the radio.

Packet radio

Using AX.25+agwpe within pat in combination with Direwolf -- but this combination felt a bit slow (which might only be my subjective opinion).

Someone might want to tune direwolf for better throughput or more reliable connections, but I'm not a direwolf expert and I rarely use it in favour of VARA FM.

Besides that, I never used packetradio on HF yet. (300bps)

  "ax25": {
    "engine": "linux",
    "rig": "",
    "beacon": {
      "every": 3600,
      "message": "Winlink P2P",
      "destination": "IDENT"
    }
  "agwpe": {
    "addr": "127.0.0.1:8000",
    "radio_port": 0
  },

The agwpe section is used by Direwolf:

$ direwolf -c /etc/direwolf/direwolf.conf -p
Dire Wolf version 1.7
Includes optional support for:  gpsd hamlib cm108-ptt dns-sd

Reading config file /etc/direwolf/direwolf.conf
Audio device for both receive and transmit: plughw:1,0  (channel 0)
Channel 0: 1200 baud, AFSK 1200 & 2200 Hz, A+, 44100 sample rate.
Ready to accept AGW client application 0 on port 8000 ...
Ready to accept KISS TCP client application 0 on port 8001 ...
DNS-SD: Avahi: Failed to create Avahi client: Daemon not running
Virtual KISS TNC is available on /dev/pts/8
Created symlink /tmp/kisstnc -> /dev/pts/8

The direwolf.conf file looks like this (comments removed):

ADEVICE  plughw:1,0
CHANNEL 0
MYCALL OE7DRT
MODEM 1200
PTT /dev/ttyUSB0 RTS DTR
AGWPORT 8000
KISSPORT 8001
IGTXLIMIT 6 10

Direwolf will warn you if the input audio level is way off; I adjust them with the program alsamixer (F6 to select the USB soundcard, then F5 to list all devices, disable Auto Gain Control with m (mute)).

Direwolf handles the PTT via the RTS line of the Digirig.

VARA FM

The corresponding configuratoin in the pat config file:

  "varafm": {
    "addr": "127.0.0.1:8300",
    "bandwidth": 0,
    "rig": "my_rig",
    "ptt_ctrl": true
  },

Start rigctld with a Dummy model - just to use the USB port of the Digirig for PTT:

$ rigctld -m 1 -p /dev/ttyUSB0 -P RTS -s 9600 -vvvv

I start VARA FM by running a small script called varafm.sh:

#!/usr/bin/sh
# Start VARA via wine

WINEPREFIX=/home/dominic/.wine-winlink wine "C:\\VARA FM\\VARAFM.exe"

In VARA FM set the USB soundcard, adjust the volume in alsamixer and on your radio, set PTT to VOX -- I tried to use COM1 but that crashed wine several times (that is why I set up rigctl before).

If you need to stop rigctl: you can usually do that with CTRL + C but this might not work. So either stop the running pat process by hitting CTRL + C in the "pat terminal" or by killing rigctld with kill $(pgrep rigctld).

I also adjust the volumes while connecting to keep the ALC (DIG gain on the TX-500) correct and also the input volume in VARA FM.

VARA HF

Back to the TX-500, the pat configuration looks like:

  "varahf": {
    "addr": "127.0.0.1:8300",
    "bandwidth": 2300,
    "rig": "my_rig",
    "ptt_ctrl": true
  },

I start rigctld like:

$ rigctld -m 2050 -r /dev/ttyUSB0 -d /dev/ttyUSB0 -p /dev/ttyUSB0 -P RTS -s 9600 -vvv

This is for the CAT protocol Lab599. If you use the older implementation (Kenwood TS-2000) start rigctl with model 2014:

$ rigctld -m 2014 -r /dev/ttyUSB0 -d /dev/ttyUSB0 -p /dev/ttyUSB0 -P RTS -s 9600 -vvv

Mobilinkd

{{< alert "circle-info" >}} The Mobilinkd TNC4 is a KISS TNC and does not provide a USB soundcard -- I only use the Mobilinkd in conjunction with packet radio. {{< /alert >}}

Winlink

I will use AX.25+linux in pat with the TNC4 paired via Bluetooth.

First of all, power on the TNC4 and pair it -- I use blueman-manager for this.

Then we need the serial port -- right click on TNC4 Mobilinkd and select Connect with Serial port

That will create a serial port at /dev/rfcomm0.

You can also create rfcomm0 in the terminal (you need the package extra/bluez-deprecated-tools for this):

$ hcitool scan
Scanning ...
    34:81:F4:AA:89:4F	TNC4 Mobilinkd
$ sudo rfcomm connect 0 34:81:F4:AA:89:4F
Connected /dev/rfcomm0 to 34:81:F4:AA:89:4F on channel 1
Press CTRL-C for hangup

Leave that terminal window open, if you are finished with your operation hit CTRL+C to disconnect the serial port.

$ hcitool scan
Scanning ...
    34:81:F4:AA:89:4F	TNC4 Mobilinkd
$ sudo rfcomm bind 0 34:81:F4:AA:89:4F

You can work within this terminal but you have to release the port when you are finished.

$ sudo rfcomm release 0

In order to use it in pat, we need to use kissattach on that serial device.

First we need to setup an AX.25 port called wl2k in /etc/ax25/axports:

# /etc/ax25/axports
#
# The format of this file is:
#
# name callsign speed paclen window description
#

#1	OH2BNS-1	1200	255	2	144.675 MHz (1200  bps)
#2	OH2BNS-9	38400	255	7	TNOS/Linux  (38400 bps)
wl2k  OE7DRT  1200  255 7 Winlink

This needs also some configuration work in the pat configuration:

  "ax25_linux": {
    "port": "wl2k"
  },
  "serial-tnc": {
    "path": "/dev/rfcomm0",
    "serial_baud": 9600,
    "hbaud": 1200,
    "type": "Kenwood",
    "rig": ""
  },

Now we can attach a KISS interface to the serial port:

$ sudo kissattach /dev/rfcomm0 wl2k
AX.25 port wl2k bound to device ax0

Select your PacketRadio Gateway (CALLSIGN-10 usually) and connect using AX.25+linux.

To de-attach the KISS interface we need to kill the process:

```
$ sudo kill $(pgrep kissattach)
```
or
```
$ sudo pkill kissattach
```

APRS with Xastir

Find the TNC4:

$ hcitool scan
Scanning ...
	34:81:F4:AA:89:4F	TNC4 Mobilinkd

Create the serial port:

$ sudo rfcomm bind 0 34:81:F4:AA:89:4F

We use /dev/rfcomm0 in Xastir.

To disconnect the device:

$ sudo rfcomm release 0

SignaLink USB

I haven't used this now for a while, but I wanted to include this in this list, as it provides a USB soundcard to the computer just like the Digirig does -- but it does not provide a serial interface to control the PTT.

Packet radio

Start direwolf (using the same configuration as with the Digirig), it will complain about not finding /dev/ttyUSB0 for PTT control. I don't use this that often and I don't use another USB device at the same time so I don't care about this. If you have another device connected as /dev/ttyUSB0 you should probably remove its reference from the direwolf configuration file.

As mode I select AX.25+agwpe and I set the output volume of the PCM2906C Audio CODEC to 100% -- the SignaLink USB will now control the PTT.

VARA FM

Start VARA FM (I use my script mentioned above) and select the proper sound card. The input volume level can be adjusted with the volume knob on the radio and the RX knob on the SignaLink USB. The output volume level can be checked and adjusted with the tune function withing the Soundcard menu from within VARA FM. You may also try the Auto-tune function.

VARA HF

I never tested this because I have no cable for the TX-500 and the SignaLink USB, but as the Signalink only provides a soundcard you have to add another USB cable for CAT control of the radio. You then start rigctld with the proper values for that specific radio.

{{< alert "circle-info" >}} That is the reason for the Digirig that combines these two functions in one device. {{< /alert >}}

Some systemd unit-file examples

Put them into $HOME/.config/systemd/user. I created them at the beginning of my "Linux Winlink journey" but actually I only let pat start the webgui at boot - the other stuff I start with scripts or I search the command history (autocomplete) in my shell.

I don't even let pat listen to something because this is my main laptop and I like the services started in a terminal window.

pat

[Unit]
Description="pat winlink"
After=network.target rigctld.service ardopc.service
Wants=rigctld.service ardopc.service

[Service]
Type=simple
ExecStart=/home/dominic/bin/pat --listen "ardop,telnet" http
TimeoutSec=10

[Install]
WantedBy=default.target

rigctld

[Unit]
Description="rigctld for TX-500 using Digirig"
After=network.target
Before=pat.service ardopc.service

[Service]
Type=simple
; -m 2050 for Lab599 TX-500 CAT protocol
; ExecStart=/usr/bin/rigctld -m 2050 -r /dev/ttyUSB0 -p /dev/ttyUSB0 -P RTS -s 9600 -vvvv
; -m 2014 for Kenwood TS-2000 CAT protocol
; ExecStart=/usr/bin/rigctld -m 2014 -r /dev/ttyUSB0 -p /dev/ttyUSB0 -P RTS -s 9600 -vvvv
ExecStart=/usr/bin/rigctld -m 2014 -r /dev/ttyUSB0 -d /dev/ttyUSB0 -p /dev/ttyUSB0 -P RTS -s 9600 -vvvv
TimeoutSec=10

[Install]
WantedBy=default.target

You can change the used protocol (Kenwood TS-2000 or Lab599 TX-500 for CAT control within the menu on the TX-500 (last menu setting)).

ardopc

[Unit]
Description="ardopc for TX-500 using Digirig"
After=network.target
Before=pat.service

[Service]
Type=simple
; ExecStart=/home/dominic/bin/ardopc 8515 hw:1,0 hw:1,0 -c /dev/ttyUSB0:9600 -p /dev/ttyUSB0:9600
ExecStart=/home/dominic/bin/ardopc 8515 plughw:1,0 plughw:1,0
TimeoutSec=10

[Install]
WantedBy=default.target

Maybe hw:… works better, but I had less trouble when using plughw:….

Decoding other stations

APRS

With direwolf

This also sends a beacon and the received stations to APRS-IS. You can watch it on https://aprs.fi.

$ rtl_fm -M fm -f 144.8M -p 36 -s 24000 -g 42 - | direwolf -c sdr-1200bps.conf -r 24000 -D 1 -B 1200 -

The direwolf configuration:

ACHANNELS 1
ADEVICE null null
CHANNEL 0

MYCALL {callsign}
IGLOGIN {callsign} {passcode}
IGSERVER rotate.aprs2.net

MODEM 1200

AGWPORT 8000
KISSPORT 8001

PBEACON sendto=IG delay=0:30 every=30:00 symbol="igate" overlay=R lat=X long=Y alt=in_meter comment="144.8MHz Receive-only gateway AFSK 1200bps"

IGTXLIMIT 6 10

With multimon-ng

$ rtl_fm -f 144.8M -g 42 -s 22050 -l 20 - | multimon-ng -t raw -a AFSK1200 -

With sdrangel

Add a channel and select Packet Demoulator.

Once packet gets demodulated, add a feature and select APRS:

The APRS feature windows let you connect to APRS-IS (top right of the APRS window).

You can also add another feature called Map to display the received APRS packets on a map.

Packet radio

With direwolf

$ rtl_fm -f 144.950M -M fm -s 200000 -r 32000 -g 35 | direwolf -n 1 -r 32000 -b 16 -t 0 -

$ rtl_fm -M fm -f 144.950M -s 22050 | direwolf -n 1 -r 22050 -b 16 -

With sdrangel

Add a channel and select Packet Demoulator.

VARA HF

We can only decode with VARA HF in monitor mode. It is possible that we can't decode anything.

POCSAG

With multimon-ng

$ rtl_fm -M fm -f 438.025M -s 22050 | multimon-ng -t raw -a POCSAG512 -a POCSAG1200 -a POCSAG2400 -a FLEX -f alpha -

With sdrangel

Set the frequency to 438.025 MHz (in Austria) and add a channel (pink mark box). Select Pager Demodulator and start decoding (click the Play button).

That will decode the set POCSAG modulation (defaults to 1200 baud).

14 KiB Raw Blame History

Digirig

Packet radio

VARA FM

VARA HF

Mobilinkd

Winlink

APRS with Xastir

SignaLink USB

Packet radio

VARA FM

VARA HF

Some systemd unit-file examples

pat

rigctld

ardopc

Decoding other stations

APRS

With direwolf

With multimon-ng

With sdrangel

Packet radio

With direwolf

With sdrangel

VARA HF

POCSAG

With multimon-ng

With sdrangel

14 KiB

Raw Blame History